Why Is There No Water in My Toilet Tank? 

Did you just try to flush your toilet, and nothing occurred? Look within the tank, and you might see no water inside. Before you stress, rest easy that fixing this issue is usually easy to accomplish. If you can’t do it yourself, you can always schedule toilet repair with an experienced plumber. Follow these recommendations to diagnose and repair the problem of no water in the toilet tank. 

Check the Water Supply 

The first move is to ensure that the water is running. If you or someone in your household recently performed a toilet repair, you probably turned off the water first. Did you neglect to turn it back on? To find out, turn the water shut-off valve on the wall to the rear of the toilet. If the valve was closed, water should now start refilling the tank. If this doesn’t work, test the water at your sink or another plumbing fixture. If nothing flows from the tap, you might have a more substantial water supply issue. Contact your water company to get more details. 

Reposition or Replace the Float Mechanism 

Older toilet models use a float ball to measure the water level as it goes up in the tank. When the ball passes a certain height, the float arm it’s attached to stops the water flow. However, insufficient water may enter the tank if the ball is positioned wrong or the arm is damaged. To adjust the float ball, start by removing the toilet tank lid. Bend the float arm up a little to adjust where it sits in the tank. If this doesn’t fix the problem, you might need to replace the whole float mechanism. You should be able to complete this yourself by following the detailed steps that come with the replacement parts, or you can employ a plumber for help. Just note that float balls are old toilet design. You may enjoy improved durability and efficiency if you upgrade the existing tank components or replace the toilet entirely. 

Adjust the Fill Valve 

Newer toilets use a float cup instead of a float ball, coupled with a fill valve and water level rod. There may very well be no water in the toilet tank because the valve has slipped out of place or become blocked. Here are some to attempt: 

  • Adjust the fill valve: Have a look inside the toilet and identify the fill valve on top of a vertical tube device on the left side of the tank. Make sure it’s secure and evenly connected to the tube. Then, fine-tune the water level. More modern toilets have an adjustment knob you can turn by hand, while older models may require you to loosen an adjustment screw with a flathead screwdriver. Flush the toilet and allow the tank refill to test the water level. Change it until the water comes to {about|approximately|roughly]] one inch below the top of the overflow tube. 
  • Clean the fill valve: Mineral buildup and other debris could be covering the valve and preventing your toilet from filling. Shut down the water behind the toilet and take away the fill cap. Then, gradually turn the water back on, cupping your hand over the valve to stop water from spraying everywhere. After several seconds, turn the water back off. Finally, wash the fill cap to dislodge any hard water buildup. If the cap is broken, buy a new one. 
  • Clean the valve tube: The tube below the fill valve may also be clogged. Shut off the water and take away the valve hardware. Then, stick a slim bottle brush or wire down the tube. Turn the water back on just a little to flush away the blockage. Replace the valve hardware and flush the toilet to check your adjustments. 

Repair or Replace the Trip Assembly 

If you’ve attempted the steps above without success, the last possibility is a broken trip assembly. This element links the flush handle to the tank. If it’s broken or positioned inadequately, the flush cycle may not complete, leaving the tank bone dry. Remove the toilet tank lid and check the trip assembly fastened to the handle. If it’s out of place, reposition it. If the assembly is twisted, worn or broken, change it out. Whether you perform the job yourself or leave it to a plumber, this uncomplicated repair should get your toilet tank filled with water again. 

Schedule Toilet Repair Today 

You can’t go long without a working toilet, so call [Company name] to request a toilet repair. We can determine why your toilet isn’t filling and suggest the right fix. If your plumbing fixture is outdated and worn out, our team can install a high-efficiency toilet in your home. Rest assured that every plumbing repair and replacement we perform is backed by a 100% satisfaction guarantee. To schedule a visit from one of our licensed crews, please contact your local Service Experts Heating, Air Conditioning & Plumbing office today. 

Savings For You

See All Offers Here >

$50 OFF Any Repair

  • Save $50 on a Paid Service
  • Written 100% Satisfaction Guarantee
  • Plus, ask how to save an additional 15% and waive your trip charge!

Free Plumbing Inspection

  • Prevent costly damage from water leaks, drain clogs and tank damage
  • Written 100% Expert Service Guarantee

© 2023 Service Experts, Service Experts Heating & Air Conditioning, and the Service Experts logo and design are registered trademarks of Service Experts LLC and used under license by SE Canada Inc. All Rights Reserved. *Not applicable to the Advantage Program. See your signed Advantage Program Agreement for full details and exclusions. 100% Satisfaction Guarantee is subject to certain restrictions and limitations as set forth in the applicable Terms and Conditions.